| Force Gauges - Special Attachments |
| Attachment |
Description |
Capacity |
Picture |
Small
Pin Grips
FG-M6PIN05
FG-M6PIN1
FG-M6PIN2 |
Ideal
for gripping fine wires and filaments; three ranges for checking
samples of .02", .04", .08" (0.5, 1 and 2 mm)
thick. |
22
lb (11 kg) |
 |
Small Pin Grips
PC-0.5
PC-1
PC-2 |
Ideal for gripping small diameters wires, pins, filaments, etc.
Three sizes cover a range of diameters. Max load 22lbs (10kg) |
PC-0.5 - for 0.5 diameter sample
PC-1 for 0.5 to 1.0 mm diameter sample
PC-2 for 1.0 to 2.0mm diameter sample |
 |
Fine Point Grips
FG-M6FPG3
FG-M6FPG8 |
Perfect for testing fine and medium gauge wire,
ribbon, tape and paper. Two jaw widths and load capacities are available; both can handle material thickness up to
.04" (1 mm) |
30 lb (15 kg)
.12" (3 mm)
60 lb (30 kg)
.31" (8 mm) |
 |
Fine Point Grips
SC-3
SC-8 |
Ideal for testing small to medium gauge wire, small components, other pull
tests. This grip can be used for measuring the strength of ribbon, wire,
etc.
|
3mm max load is 22lbs
(10kg).
8mm max load is 35lbs (16kg) |
 |
Film Grips
FG-M6FLM20
FG-M6FLM50U |
These heavy-duty, spring-loaded grips have serrated jaws for handling samples up to .39" (10 mm) thick and .79" (20 mm)
or 1.97" (50 mm) wide. |
100 lb (50 kg) |
 |
Thin Film Grip
FC-20 (20mm)
FC-40 (40mm) |
Use these spring-loaded film grips to check the tensile strength of thin
film samples (up to 2mm thick). |
110lbs (50kg) |
 |
Jacob’s
Chuck Grips
FG-M6JAC5U |
Designed
for testing low gauge wire and rigid rods; accepts material
diameters from .02" (.05 mm) to .20" (5 mm). |
100
lb (50 kg) |
 |
Jacob's Chuck
GC-5 |
For use with shafts/rods from 0.5mm to 5mm. |
110lbs
(50kg) |
 |
Flat
Chuck
Tensile Grips
FG-M6FTG20U |
Each
serrated gripping face is .79" (20 mm) square and can accept samples up to .79" (20 mm) thick. |
100 lb
(50 kg) |
 |
Flat Chuck
GC-10
10mm opening
GC-20
20mm opening |
20mm square serrated face, heavy-duty
flat chuck. |
110lbs (50kg). |
 |
Spool Grips
FG-M6SP010U
|
Ideal for
hard-to-hold items like thread, filaments, etc. The sample is wrapped around the spool, anchored by
friction.
|
100 lb (50 kg)
|
 |
Wire Wrapping Grip
GT-20-3 |
For measuring the strength of wires,
filaments, fibers, etc. |
110 lbs (50kg) |
 |
Tape Grips
FG-M6TAP30U
|
Self-tightening
lever action makes this fixture perfect for testing rubber, tape and paper.
|
100 lb (50 kg)
|
 |
Wedge Grips
FG-M6WDG50U
|
Two
capacities for lighter and heavier loads; spring-loaded jaws automatically close on the
specimen and
tighten as tension is applied. Ideal for testing wires, strip material and
plastic tape or films. |
100 lb (50
kg)
500 lb (250 kg)
|
 |
Heavy-Duty
Tensile Grip
FG-M10TEN7U
FG-TEN7B
|
Manually
tightened jaw faces can accept samples 1.25" (31.75 mm) wide and .25" (6.35 mm) thick.
Contact faces are serrated hardened tool steel.
|
500 lb (250 kg)
|
 |
Clevis Grips
FG-M10CLV10U
FG-CLV10B
|
Odd shaped
parts, punched samples or tension springs are easily secured and
tested. Concave shape to pins
assures centering under load. Throat clearance with pin is
.5" (12.7 mm) and can easily accept samples up to .375"
(9.65 mm) wide.
|
500 lb (250 kg)
|
 |
Cord and Twine Grips
FG-M10TWN500U
FG-TWN500B
|
A
unique figure 8 wrap of specimen assures a center break and non-locking pins permit quick installation and
release. Throat and pin clearance is
.375" (9.65 mm) wide with the throat width being .5" (12.7 mm).
|
500 lb (250 kg)
|
 |
Fabric Grips
FG-M10FAB80U
FG-FAB80B
|
Eccentrically
mounted, serrated roller grips allow for self- tightening of
specimens up to 3" (76.20 mm)
wide and .25" (6.4 mm) thick. |
500 lb (250 kg)
|
 |
Adhesive Test Plates
FG-M10ADHE3
|
Samples
up to 3" (76.20 mm) in diameter can be tested with hardened tool steel detachable faceplates. Ball
socket mounting screws in both grips assure parallelism and perpendicularity
to force when load is applied.
|
500 lb (250 kg)
|
 |
Wire Terminal
Test Fixture
FG-M6WTER100
|
Designed
specifically to test the strength of wire/terminal connections. The upper grip consists of a
self-aligning wheel with nine equally spaced slots of various terminal shank
sizes; an eccentrically mounted, self-tightening bottom grip secures
the wire on the other end.
|
100 lb (50 kg)
|
 |
| Compression Plates |
Hardened
compression plates available - contact distributor 100 lb (50 kg) regarding part number and pricing.
|
500 lb (25 kg)
|
|
| Penetrating
Pin Gauge |
Use this unique attachment to check the hardness of clay-like materials, the burst
strength of plastic coverings / skins, etc. |
|
PG-2 |
2mm OD |
20LB Max Load |
|
PG-3 |
3mm OD |
20LB Max Load |
|
PG-4 |
4mm OD |
45LB Max Load |
|
PG-5 |
5mm OD |
45LB Max Load |
|
 |
Wedge Grip
KC-100 |
This spring-loaded grip is ideal for tensile measurements of thick
materials (up to 10mm thick). The serrated jaw is 15mm wide.
|
500lbs (230kg) |
 |
X-Y Table
GT-20-3 |
±30mm movement for both X & Y axes. |
110 lbs (50kg) |
 |
Bend Test Stand
GA-10 |
Test
the bend strength of rods, strips, etc. 40mm wide. |
110lbs
(50kg). |
 |
Tape Grip
GC-60 |
Self tightening "buckle-type" mechanism
ensures slip-free operation. For use with tapes to 30mm wide |
110lbs (50kg). |
 |
Vise Chuck
GT-30 |
Screw tightened vise is ideal for
slip-free attachment to base of test stand. 38mm wide, jaw opens to
39mm. |
110lbs (50kg) |
 |
Large Flat Head
AA-30 |
Suitable for general push/crush testing.
30mm OD |
110lbs (50kg) |
 |
Universal Joint
UJ-6 (fits M6P1 shaft)
UJ-10
(fits M10P1.5 shaft) |
Flexible coupling fits between measuring
shaft and attachments. |
110lbs (50kg) |
 |
Peeling Attachments
PF-1 pull test peeling
PF-2
push test peeling |
Use these unique attachments to measure the peel force of laminated
materials, etc.
|
|
 |
Adapter Coupling
TJ-6
TJ-10 |
TJ-6 connects M6P1 shaft to # 10-32 thd
TJ-10 connects M10P1.5 shaft to #5/16-1 thd |
110lbs (50kg) |
 |
Pin Joint
PJ-6 (fits M6P1 shaft)
PJ-10 (fits M10P1.5 shaft)
|
Flexible coupling fits between measuring
shaft and attachments |
110lbs (50kg) |
 |
